How to Install a Bathroom Exhaust Fan

How to Install a Bathroom Exhaust Fan

1. Find or Establish the Power Source

   Turn off the electricity to the existing ceiling light by flipping off the circuit breaker at the service panel. The bathroom vent fan will be installed in the ceiling. You may already have power running to the exact point where you intend to install the bathroom vent fan. Depending on your local electrical code, you may be able to share your bathroom lighting circuit with the fan. The bathroom lighting circuit usually supplies power to your bathroom's ceiling light. Alternatively, you can substitute the light for a fan/light combination.

   If your code requires you to run a dedicated circuit for the fan, you can run a new cable from the service panel to the bathroom ceiling area. If you do not feel comfortable establishing new circuits and working with the service panel, contact an electrician to complete this task.

2. Locate the Vent Point

   • Run a duct from the fan to either the roof or a side wall so the air can be exhausted outdoors. If at all possible, run the flexible ducting to a wall, as this helps you avoid shingle work and the possibility of roof leaks. 
   • Choose a spot for the vent location that is a direct route from the fan to the outside and 6 feet or less away from the bathroom fan to the exit point. The vent fan needs to be in the bathroom interior, not in a hallway, and should be located close to the shower, tub, or shower/tub combination, as this is the area that produces the most moisture. The duct leading from the vent should be as straight as possible to avoid sharp bends that can impede airflow.
   • Drill a locator hole at the center of the intended location.

3. Cut the Exterior Vent Location

   • Access either the wall or the roof of the house as your point of intention to exhaust to the exterior.
   • Bring your round vent (for walls) or vent cap (for roofs). Also bring your reciprocating saw, cordless drill, pencil, and silicone caulk.
   • Situate the round vent or vent cap across the locator hole. With the pencil, scribe a circle where the vent or cap will fit. 
   • Use the reciprocating saw to cut the circle, with the locator hole as a start point for the saw blade.
   • Attach the round vent or roof cap with screws, first applying silicone caulk to ensure a watertight fit.
     

   Tip

   On a roof, you will need to slip the flashing of the roof cap under the shingles above the midsection of the vent opening to ensure a watertight installation. This may require removing some shingle nails and/or trimming the surrounding shingles to fit around the roof cap.

4. Cut the Interior Opening for the Bathroom Fan

   • Use the stud finder from below to locate the joists in the bathroom ceiling and lightly mark with a pencil.
   • Use the template (if available) to mark the intended location of the fan in the ceiling. If there is no template, use the metal fan housing itself (leave the fan assembly out for now). Many bathroom fans screw directly to the side of the joist. If so, place the template or housing parallel to a joist when making the cut lines.
   • Cut out the drywall carefully with the jab saw.

5. Attach the Bathroom Fan to the Joist

   • Access the attic and bring your light, cordless drill, screws, and bathroom fan housing. Place the fan in the cut-out hole so that the bottom edge of the fan is flush with the bottom of the ceiling drywall. You will need a partner for this step, as you cannot see the ceiling from this position.
   • Screw the fan into the side of the joists with the cordless drill. If you cannot use the side of a joist as an attachment point, your fan may come with suspension brackets. If not, you can purchase these separately. Brackets will allow the fan to be suspended in a position that is not adjacent to a joist.
   • While you are still in the attic, fit the electrical wire through the side of the housing so that roughly 7 inches of the wire extends into the housing.

6. Route the Bathroom Fan to the Exterior

   • Go back down to the bathroom and verify the vertical placement of the fan.
   • Gather your flexible ducting and aluminum foil tape and take it back into the attic.
   • Use the foil tape to attach the flexible tubing to the fan and the vent. (Your fan or ducting may come with mechanical fasteners for attaching the duct to use instead of foil tape). Ensure that the tubing runs as smoothly and directly as possible.

7. Attach the Bathroom Fan to the Housing

   • Insert the fan unit into the housing in the bathroom, per the manufacturer's instructions.
     

8. Wire the Switch

   • Strip the ends of the electrical wires and hard-wire them into the unit. Typically, either a bare wire or green wire will attach to the side of the metal housing for grounding, a critical safety measure.

9. Attach the Grille

   • Attach the fan grill to the face of the housing.
   • Turn the circuit breaker back on.
   • Return to the bathroom and test the fan by turning on the switch.